ACL-380 Surface Resistance Tester

The ACL-380 surface resistance tester can measure both surface impedance and resistance to ground, with a wide range from 103 ohms to 1012 ohms, with an accuracy of ±1/2 range. The ACL-380 surface resistance tester adopts the ASTM standard D-257 parallel electrode sensing method, which can easily and repeatedly measure various conductive, electrostatic discharge, and insulating surfaces. use: To measure the surface impedance, place the meter on the surface to be measured, press and hold the red measurement (TEST) button, the continuously lit light-emitting diode (LED) indicates the magnitude of the measured surface impedance. 103=1 kiloohm　　　　　 green LED 104=10k ohm　　　　 green LED 105=100kohm 　　　 green LED 106=1 megaohm 　　　　 yellow LED 107=10 megaohm 　　　 yellow LED 108=100 megaohm 　　　 yellow LED 109=1000 megaohm 　　　yellow LED 1010=10000 megaohm 　　 yellow LED 1011=100000 megaohm 　　 yellow LED 1012=1000000 mega ohm 　 red LED > 1012=insulated red LED Measure resistance to ground Insert the ground wire into the ground socket, so as to insulate the right side detection electrode of the meter (on the same side as the socket). Connect the alligator clip to your ground wire. Place the meter on the surface to be measured, press and hold the TEST button, and the continuously illuminated LED indicates the magnitude of the resistance to ground. The unit of this measurement is ohms. parameter: Electricity source: 9V PP3 alkaline battery Measuring voltage: Rated 9 volts Relative humidity: 0%～90% (no condensation) Precision: ±10% Repeat error: ±5% Weight: 170g (60Z) Ruler 　　inch: 127×76×26 ACL-380 surface impedance meter calibration method Calibration cycle: The ACL-380 surface impedance meter needs to be calibrated every twelve months. Using a decimal resistance box, connect the standard measuring resistance across the two parallel electrodes of the ACL-385 meter to check whether the displayed impedance value is correct. Parameters: Power supply: 9V PP3 alkaline battery Measuring voltage: 9 volts Temperature range: operating temperature 5 degrees Celsius to 49 degrees Celsius Storage temperature: -15 degrees Celsius to 60 degrees Celsius Relative humidity: 0% to 90% (non-condensing state) Measurement degree: 10 orders of magnitude Transition point: 1/2 level logarithm (3.16×10n) Transition point accuracy: ±1/2 level Accuracy: ±10% Repeatability: ±5% Weight: 170g Size: 130×70×25 (millimeter unit)

Category:

Surface Resistance Meter

Lables:

隐藏域元素占位

Messages

sales@feita.ltd

Product Detail

The ACL-380 surface resistance tester can measure both surface impedance and resistance to ground, with a wide range from 103 ohms to 1012 ohms, with an accuracy of ±1/2 range. The ACL-380 surface resistance tester adopts the ASTM standard D-257 parallel electrode sensing method, which can easily and repeatedly measure various conductive, electrostatic discharge, and insulating surfaces.

use:

To measure the surface impedance, place the meter on the surface to be measured, press and hold the red measurement (TEST) button, the continuously lit light-emitting diode (LED) indicates the magnitude of the measured surface impedance.

103=1 kiloohm　　　　　 green LED

104=10k ohm　　　　 green LED

105=100kohm 　　　 green LED

106=1 megaohm 　　　　 yellow LED

107=10 megaohm 　　　 yellow LED

108=100 megaohm 　　　 yellow LED

109=1000 megaohm 　　　yellow LED

1010=10000 megaohm 　　 yellow LED

1011=100000 megaohm 　　 yellow LED

1012=1000000 mega ohm 　 red LED

> 1012=insulated red LED

Measure resistance to ground

Insert the ground wire into the ground socket, so as to insulate the right side detection electrode of the meter (on the same side as the socket). Connect the alligator clip to your ground wire.

Place the meter on the surface to be measured, press and hold the TEST button, and the continuously illuminated LED indicates the magnitude of the resistance to ground. The unit of this measurement is ohms.

parameter:

Electricity source: 9V PP3 alkaline battery

Measuring voltage: Rated 9 volts

Relative humidity: 0%～90% (no condensation)

Precision: ±10%

Repeat error: ±5%

Weight: 170g (60Z)

Ruler 　　inch: 127×76×26

ACL-380 surface impedance meter calibration method

Calibration cycle:

The ACL-380 surface impedance meter needs to be calibrated every twelve months.

Using a decimal resistance box, connect the standard measuring resistance across the two parallel electrodes of the ACL-385 meter to check whether the displayed impedance value is correct.

Parameters:

Power supply: 9V PP3 alkaline battery

Measuring voltage: 9 volts

Temperature range: operating temperature 5 degrees Celsius to 49 degrees Celsius

Storage temperature: -15 degrees Celsius to 60 degrees Celsius

Relative humidity: 0% to 90% (non-condensing state)

Measurement degree: 10 orders of magnitude

Transition point: 1/2 level logarithm (3.16×10n)

Transition point accuracy: ±1/2 level

Accuracy: ±10%

Repeatability: ±5%

Weight: 170g

Size: 130×70×25 (millimeter unit)
Key words:
- acl-380
- led
- surface
- resistance
- megaohm
- meter

ACL800C surface resistance tester

none

Message

If you need a solution, you can write your question and contact information in the message form, we will contact you as soon as possible after receiving it.

Action